PCB DESIGN · ARTWORK

From Circuit to Board,
From Board to Reliability.

From schematic design and PCB artwork to verification, release, prototyping and assembly. INSPIRNET, which understands the needs of medical, industrial and automotive sites, handles it all through one point of contact.

SCHEMATIC · LAYOUT · VERIFICATION · BUILD

Altium-based PCB layout design screen
OVERVIEW

Design Quality Determines Product Lifetime

PCB design is not simply redrawing a schematic. Every placement and every trace affects noise, heat and manufacturing yield. INSPIRNET reads the flow and characteristics of each circuit and designs boards that hold up through mass production. Our experience developing medical, industrial and automotive equipment directly sets our design standards.

~24 layers
Multilayer board design
50/50 μm
Min. trace / space
0.4 mm
Min. BGA pitch
Altium
Primary design CAD
SERVICES

Scope of Services

From a single schematic to an assembled board, you can outsource just the stages you need.

SCHEMATIC DESIGN

Schematic Design

We turn your requirements into schematics. If you already have a schematic, we start with a review.

  • Block diagram
  • Schematic capture & review
  • Component selection
PCB LAYOUT

PCB Artwork

We place and route components according to circuit flow and characteristics, including high-density multilayer boards.

  • Component placement
  • Layer stack-up design
  • High-speed signal routing
LIBRARY BUILD

Library Development

We build Schematic, PCB and 3D libraries and manage them from a single source.

  • Schematic symbols
  • PCB footprints
  • 3D models
DRC · DFM

Design Verification

Netlist cross-checks and design and manufacturing rule reviews catch errors before release.

  • Netlist cross-check
  • DRC review
  • DFM review
MANUFACTURING DATA

Manufacturing Data Release

We organize deliverables into a form that can be used for fabrication right away.

  • Gerber · drill
  • BOM · assembly drawing
  • Stack-up specification
PROTOTYPE & ASSEMBLY

Prototype & Assembly Support

Beyond design, we connect PCB fabrication and SMT assembly through a single point of contact.

  • PCB fabrication
  • SMT assembly
  • Component sourcing

Not sure which stage you need? Send us the schematic and we will review it for you.

INSPIRNET DESIGN INTEGRITY

Design Integrity System IDI

We do not rely on individual designer skill alone. Libraries, verification and history are managed as one system so that every project reaches the same quality, regardless of who leads it.

LIBRARY INTEGRITY

Library Integrity

We manage Schematic, PCB and 3D libraries from a single source, eliminating part definitions that differ from project to project.

  • Standard symbol & footprint specifications
  • Concurrent 3D model management
  • Cross-project library consolidation
NET INTEGRITY

Connectivity Integrity

Design results are checked against the schematic to catch connection errors before release. This is the final checkpoint in INSPIRNET's design process.

  • Netlist cross-check review
  • DRC rule verification
  • DFM manufacturability review
PROCESS INTEGRITY

Process Integrity

Design data and revision history are kept in a standard system, so traceability is not lost in later revisions or the transfer to mass production.

  • Revision history management
  • Standardized deliverables
  • Design data archiving
IDI design integrity system — integrated library management and net review screen
DESIGN FLOW

Six-Stage Design Process

From intake to release, we share in advance what is checked at each stage.

  1. Requirements & Circuit Review
    01REVIEW

    Requirements & Circuit Review

    We receive the schematic and specifications and confirm the design constraints. Work begins after an NDA is signed.

  2. Library & Component Confirmation
    02LIBRARY

    Library & Component Confirmation

    We finalize symbols, footprints and 3D models, and review component availability as well.

    IDI · LIBRARY Integrity
  3. Placement
    03PLACEMENT

    Placement

    We place components considering mechanical fit, heat and noise, and finalize the layer stack-up.

  4. Routing
    04ROUTING

    Routing

    We apply impedance control, differential pairs and length matching to secure signal quality.

  5. Verification
    05VERIFICATION

    Verification

    Netlist cross-checks and DRC/DFM reviews remove errors before release.

    IDI · NET Integrity
  6. Release & Fabrication Handover
    06RELEASE

    Release & Fabrication Handover

    We generate Gerber, drill and BOM outputs and hand them over to fabrication and assembly.

    IDI · PROCESS Integrity
CAPABILITY & ANALYSIS

Design Capability · Analysis

For specifications beyond the table below, we review them and reply with whether we can support them.

PCB design capability specifications
Board layersSingle · double · multilayer (~24 layers)
Min. trace / space50 / 50 μm (2 / 2 mil)
Min. via0.20 mm · microvia 0.10 mm
Min. BGA pitch0.40 mm
HDI structure1+N+1 · 2+N+2
Special boardsRigid-Flex · Metal-core PCB
Impedance controlSingle-ended 50Ω · differential 90 / 100Ω
Supported CADAltium Designer · OrCAD/Allegro · PADS
High-speed signal impedance control and signal integrity analysis screen
SI / PI

Signal & Power Integrity

We review high-speed signal reflection and crosstalk, and power plane stability, at the design stage.

EMI / EMC

Early Noise Review

We check return paths and ground partitioning to reduce the risk of redesign during certification.

THERMAL

Thermal Review

We review heat-generating component placement and heat-spreading patterns to secure operating temperature margin.

If a specification falls outside the table or is hard to judge, sending us your materials for confirmation is usually faster.

APPLICATION

Application Areas

Each application area prioritizes different design criteria. We design to reflect the conditions of the field.

PCB design case for a medical device
MEDICAL

Medical Devices

Boards for diagnostic and imaging equipment that handle small signals. We prioritize noise suppression and safe clearances.

PCB design case for semiconductor inspection equipment
INDUSTRIAL

Industrial & Inspection Equipment

Boards for semiconductor and display inspection equipment. We support high-speed interfaces and multi-channel routing.

PCB design case for automotive electronics
AUTOMOTIVE

Automotive Electronics

Boards for automotive electronics under harsh vibration and temperature. We design for durability and manufacturing stability.

ALSOTelecom equipmentDisplaysControl systemsMultimediaInstrumentationHome networking
WHY INSPIRNET

What Sets Us Apart from Design-Only Firms

END-TO-END

End-to-End Service

From schematic design and artwork to prototyping, assembly and mass production, all handled through one point of contact. No need to manage multiple vendors.

HIGH-SPEED

High-Speed Video Signal Design Experience

We apply the high-speed, low-latency signal design know-how we built developing our own Frame Grabbers.

SUPPLY

Component Supply Linkage

Connected to our distributor and stock business, so part obsolescence and lead times are reviewed at the design stage.

RESPONSE

Prompt Local Response

We respond during business hours (09:00–18:00) from our Osan office. Design data is managed separately after an NDA is signed.

FAQ

Frequently Asked Questions

What materials should we prepare?

A schematic and a BOM are enough for us to start the review. If you have mechanical drawings, we will also check placement fit. If you do not have a schematic yet, we can begin with circuit design.

How long does it take?

It depends on the layer count, component count and signal complexity. Once we receive your materials, we will review them and provide an estimated schedule and quote.

How is design data kept secure?

We proceed after an NDA is signed. Design data is stored separately for each project, and revision history is managed so changes can be traced in future revisions.

Can you also handle PCB fabrication and assembly?

Yes. After Gerber release, we can connect you to PCB fabrication and SMT assembly, and we also support component sourcing.

CONTACT

Send Us Your Schematic
and We Will Get Back to You After Review

We check layer count, component count and signal requirements, then provide an estimated schedule and quote. Business days 09:00–18:00 KST, prompt response.

Tel
031-203-8921
Fax
031-206-8633
Design Inquiry
mason@inspirnet.com
Sales Inquiry
brian@inspirnet.com
Location
#636–637, 6F, Bldg. A, Hyundai Premier Campus Sema Station, 30 Gyeonggi-daero 761beon-gil, Osan-si, Gyeonggi-do 18112, Republic of Korea